Technical Specifications

406 AGRI

Specifications

406 Static Dims - Line Profile

STATIC DIMENSIONS

A

Overall Length

mm

5133

B

Axle to pivot pin

mm

906

C

Wheel Base

mm

2100

D

Axle to counterweight face

mm

1268

E

Ground clearance

mm

313

F

Width over cab

mm

1468

G

Width over tyres

mm

1727

H

Wheel track

mm

1390

J

Height Over Cab

mm

2500

Front axle weight

kg

1475

Rear axle weight

kg

3398

Total weight

kg

4873

Inside Turn Radius

mm

2010

Maximum Turn Radius over Shovel

mm

4160

Articulation Angle

deg

±40°

Maximum radius over tyre

mm

3800

Max. width across tyres

mm

1761

Data based on machine equipped with pin mounted 0.8m³ bucket with toe plates and Camso SLR4 12.5-18 tyres.

ENGINE

ENGINE

Type

4 stroke, Mechanical

Model

JCB Diesel by Kohler - KDI 2504 M

Capacity

litres

2.482

Aspiration

Normally aspirated

Cylinders

4

Max gross power to SAE J1995/ISO 14396

kW (hp)

36.4 (49) @ 2600rpm

Max torque

Nm @ 1500rpm

170

Emissions

Stage IIIA

TRANSMISSION

TRANSMISSION

Type

Hydrostatic

Model

Rexroth A6VM – 2 speed

Low range

kph

6

High range

kph

20

LOADER DIMENSIONS

LOADER DIMENSIONS

Model (assumes machine is fitted with Camso SLR4 12.5-18 tyres)

Bucket type

General purpose

General purpose

Light duty

Light duty

6-in-1 clam shovel

Bucket equipment

Teeth or toeplate

Toeplate

Teeth or toeplate

Bucket capacity (SAE heaped)

m³

0.8

1

1.2

1.4

0.75

Bucket width

mm

1900

1900

1900

1900

1900

Bucket weight

kg

287

322

353

384

435

Maximum material density

kg/m³

2050

1620

1320

1120

2100

Tipping load straight

kg

4225

4148

4055

4014

4033

Tipping load full turn

kg

3250

3191

3120

3088

3102

Payload

kg

1625

1595

1560

1544

1551

Maximum breakout force

kN

41.9

36.5

32.2

29.7

41.9

M

Dump angle maximum

degrees

45

45

45

45

45

N

Roll back angle full height

degrees

56

56

56

56

56

O

Roll back at carry

degrees

54

54

54

54

54

P

Roll back at ground level

degrees

42

42

42

42

42

Q

Load over height

mm

2991

2991

2991

2991

2991

R

Dump height (45 deg dump)

mm

2489

2418

2348

2295

2489

S

Dig depth

mm

105

105

105

105

106

T

Reach at dump height

mm

764

835

905

958.5

764

Reach maximum (45deg dump) – horizontal arm

mm

1494

1465

1635

1689

1494

Operating weight (includes 80Kg operator and full fuel tank)

kg

4873

4907

4938

4969

5020

V

Pin height

mm

3120

3120

3120

3120

3120

TYRE SIZE

TYRE SIZE

Dimensions

Tyre size

Manufacturer

Type

Operating weight (kg)

Vertical (mm)

Width (mm)

335/80 R18

Dunlop

SPT9 EM

41.2

-4

0

365/70 R18

Dunlop

SPT9 EM

64

-14

69

405/70 R18

Dunlop

SPT9 EM

94

9

113

335/80 R20

Dunlop

SPT9 MPT

77.6

22

-22

340/80 R18

Michelin

XMCL

71.6

28

25

340/80 R18

Michelin

BIBLOAD

65.6

-15

13

12.5-18

Mitas

MPT-04

31.6

9

-6

340/80 R18

Nokian

TRI 2

55.6

6

12

12.5/80-18

Camso

SLR4

0

1

-15

400/70 R18

Trelleborg

TH400

111.6

-15

137

Loader dimensions quoted on Camso SLR4 12.5-18 tyres.

406 Forks Line Profile

LOADER DIMENSIONS - FORK FRAME WITH FORKS

LOADER DIMENSIONS – FORK FRAME WITH FORKS

Parallel fork

Fork carriage width

mm

1345

Length of tines

mm

1200

A

Reach at ground level

mm

710

B

Reach at arms horizontal

mm

1232

C

Below ground level

mm

84

D

Arms, horizontal height

mm

1426

E

Arms, maximum height

mm

3012

F

Reach at maximum height

mm

506

Payload*

kg

2033

Tipping load straight

kg

3184

Tipping load full turn (40°)

kg

2541

Attachment weight

kg

191

*At the centre of gravity distance 500mm. Based on 80% of FTTL as defined in IS0 8313. Manual fork spacings at 50mm increments.
Fork section 100mm x 50mm.

AXLES

AXLES

Type

Straight beam

Make and model

Dana 111

Chassis angle oscillation

degrees

±10

STEERING


STEERING

Hydraulic power steering system emergency steering.

ELECTRICAL SYSTEM

ELECTRICAL SYSTEM

System voltage

Volt

12

Alternator output

Amp hour

80

Battery capacity

Amp hour

100

HYDRAULICS

HYDRAULICS

Pump type

Tandem Gear Pump

Pump max. flow

l/min

64

Pump max. pressure

bar

230

Auxiliary flow

l/min

60

Hydraulic cycle times at max. engine

Arms raise (full bucket)

Seconds

4.9

Bucket dump (full bucket)

Seconds

3.5

Arms lower (empty bucket)

Seconds

3.1

Total cycle

Seconds

11.5

SERVICE FILL CAPACITIES

SERVICE FILL CAPACITIES

Hydraulic system

litres

70

Fuel tank

litres

80

Engine oil sump

litres

11.2

Axle oil (front)

litres

4.4

Axle oil (rear)

litres

6.05

STANDARD EQUIPMENT

STAndard equipment

General machine features

Parallel lift geometry, JCB Hydraulic Quickhitch, articulated steering, front and rear fenders, one piece opening bonnet, recovery hitch, lifting lugs.

Transmission

Two speed, neutral start, inching function, forward/reverse switch on joystick control lever.

Brakes

In board oil immersed brakes with combined handbrake; cable operated parkbrake.

Electric

Full Road Lighting, Direction Indicators and Battery Isolator.

Hydraulics

Single lever manual control, gear pump with priority steer, emergency steer back up.

CAB

ROPS/FOPS safety structure, fully adjustable seat, interior light, adjustable tilt steering column, safety glass, front and rear screen wash/wipe, 3 speed heater fan with replaceable filters, sun visor.

OPTIONAL EQUIPMENT

OPTIONAL equipment

HBCV, 4th Spool aux circuit manual, LSD axles, fully opening RH window with lock back, immobiliser, livelink, under bonnet battery isolator, worklights, bio oil, shovel level indicator, stowage box. See dealer for full list.

NOISE AND VIBRATION

NOISE AND VIBRATION

Uncertaincy

Measurement conditions.

Noise at the operator station

LpA

77 dB

+/- 1 dB

Determined in accordance with the test method defined in ISO 6396 and the dynamic test condition defined on 2000/14/EC.

Noise emission from the machine

LWA

101 dB

+/- 1 dB

Guaranteed equivalent sound power (external noise) determined in accordance with the dynamic test conditions defined in 2000/14/EC.

Whole body vibration

m/s2

0.59

+/- 0.11 dB

ISO 2632-1:1997 normalised to an 8h reference period and based
upon a test cycle comprising of loader work (soil).

Hand-arm vibration

m/s2

<2.5

N/A

ISO 5349-2:2001 dynamic test conditions.